6530A REV F Norge Washer Parts List

Module shelf insert - clear (insert module)

This part is the front of the door shelf bin.

Door shelf bin (refrigerator door shelf bin)

Sold individually. Sometimes referred to as the 2-liter bin.

Upper drum glide (use 5303937139)

The upper drum felt glide kit helps to support the front drum as it rotates smoothly and quietly while operating. This kit includes three glides with the adhesive. If your dryer won’t tumble or is noisy, the glide could be worn down causing you to hear a metal on metal noise and will need to be replaced. The drum glide is a genuine OEM part and sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Rear drum bearing kit (shaft & bracket asm)

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Over time the drum bearing will wear out, once it has the dryer may make some noise and the drum bearing will need to be replaced. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power to your appliance before starting your repair.

Refrigerator water filter (use wci ultrawf)

This PureSource Ultra water filter will fit most Frigidaire french door and side by side refrigerators. The water filter is used to reduce contaminants that may be in your household water supply. It is recommend that you replace your water filter every 6 months. Sold individually.

Spray arm (use 154414201)

Surface element - 8 inch - 220v (economy plug-in surface unit - 8")

The coil burner element is eight inches in diameter. It has four turns, 220 volts and looped terminal ends. The coil burner element provides heat to the cooking surface on your range. You might need to replace this part if your element is not heating. It might have shorted out around the coil or the terminal block; you can test the coil to see if the burner or the switch may be at fault. Please make sure the power has been disconnected and the element is turned off and had time to cool before starting your repair. The element is a genuine OEM part and is sold individually.

Upper spray arm (dishwasher upper spray arm)

The upper spray arm helps distribute water from the top of the dishwasher tub. The spray arm spins on the upper support when the dishwasher is running. If the spray arm is cracked, broken, or clogged with no water coming from the spray arm, your dishes may not be cleaned properly and the upper spray arm will need to be replaced. The spray arm is 9-inch long, gray in color and made of plastic. This is a genuine OEM part. Please remember to disconnect the power and water supply to your dishwasher before starting your repair.

Control knob (knob)

This knob accepts a D-shaped shaft. Sold individually.

Drive belt - 51 inches long (washer drive belt)

This V-style drive belt is about 51-inch long and 3/8-inch wide. This part is made to slip onto the motor pulley to bring the basket up to the speed required. The belt encounters wear and tear over time. If your washer will not drain, spin, or agitate, you may need to replace your belt. It is recommended to disconnect the power to your washer before you start your repair. This V-style belt is a genuine OEM part.

Duct felt seal (trap duct felt)

The duct felt seal allows the front of the drum to glide smoothly on the exterior panel while the drum is rotating. The seal is located between the back of the drum and the rear dryer panel. If the heat is escaping from the drum area causing the dryer to run too long or if there are marks on your clothes you many need to replace the duct felt seal. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Front load washer door lock and switch assembly (door lock/switch assy)

Torx screw (screw-torx)

7-18 x 3/4" - sold individually.

Sealed burner cap with electrode (sub 12500099)

This burner cap assembly is sold with the spark electrode. Please note this part has been redesigned and no longer requires a gasket. Sold individually.

Roller tub gray (use 154213401)

The dishrack support roller attaches to the inside of the tub by a screw, to help support the upper rack. There are eight total inside the tub, four on each side. This support roller is made of plastic and is approximately 1 1/2” in diameter. The screw is not included with the roller, you can reuse the existing screw. This is a genuine part and is sold individually.